How could you prepare for your Cisco 200-105 dumps certification exam? The Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) (200-105 ICND2) exam is a 90 Minutes (45-55 questions) assessment in pass4itsure that is associated with the CCNA Routing & Switching certification.”Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)” is the exam name of Pass4itsure Cisco 200-105 dumps test which designed to help candidates prepare for and pass the Cisco 200-105 exam. Our Cisco 200-105 dumps preparation product is absolutely perfect for candidates who are in need of putting their careers on the top gear or in need of providing the brightest future for themselves. Discount Cisco https://www.pass4itsure.com/200-105.html dumps study guide Interconnecting Cisco Networking Devices exam q&as preparation Youtbube with latest version pdf&vce.
If you think you’re one of these people, our 200-105 exam demo solution will help you. without any cost, we deliver free updates demo of the 200-105 Interconnecting Cisco Networking Devices exam.
[100% Pass Guarantee Cisco 200-105 Dumps From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWWWw0QXQxY3R1X1E
[100% Pass Guarantee Cisco 100-105 Dumps From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWeVQ5WUxjZG1Idnc
★Pass4itsure Latest and Most Accurate Cisco 200-105 Dumps Exam Q&As★:
A static map to the S-AMER location is required. Which command should be used to create this map?
A. frame-relay map ip 172.30.0.3 825 broadcast
B. frame-relay map ip 172.30.0.3 230 broadcast
C. frame-relay map ip 172.30.0.3 694 broadcast
D. frame-relay map ip 172.30.0.3 387 broadcast
200-105 exam Correct Answer: B
Frame-relay map ip 172.30.0.3 230 broadcast
172.30.0.3 is S-AMER router ip address and its configure on 230 dlci value. Check andquot;show frame-relay map
andquot; output in the diagram.
The command show frame-relay map gives the following output:
Serial 0 (up): ip 192.168.151.4 dlci 122, dynamic, broadcast, status defined, active
Which statements represent what is shown?(Choose three.)
A. 192.168.151.4 represents the IP address of the remote router
B. 192.168.151.4 represents the IP address of the local serial interface
C. DLCI 122 represents the interface of the remote serial interface
D. DLCI 122 represents the local number used to connect to the remote address
E. broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC
F. active indicates that the ARP process is working
Correct Answer: ADE
Which statement about MPLS is true?
A. It operates in Layer 1.
B. It operates between Layer 2 and Layer 3.
C. It operates in Layer 3.
D. it operates in Layer 2.
200-105 dumps Correct Answer: B
Explanation: MPLS belongs to the family of packet-switched networks. MPLS operates at a layer that is generally
considered to lie between traditional definitions of OSI Layer 2 (data link layer) and
Which command is used to enable CHAP authentication, with PAP as the fallback method, on a serial interface?
A. Router(config-if)# ppp authentication chap fallback ppp
B. Router(config-if)# ppp authentication chap pap
C. Router(config-if)# authentication ppp chap fallback ppp
D. Router(config-if)# authentication ppp chap pap
Correct Answer: B
The command andquot;ppp authentication chap papandquot; command indicates the CHAP authentication is used first.
If it fails or is rejected by other side then uses PAP instead. If you want to use PAP
Which two switch states are valid for 802.1w? (Choose two.)
200-105 pdf Correct Answer: DE
Port States There are only three port states left in RSTP that correspond to the three possible operational states. The 802.1D disabled, blocking, and listening states are merged into a unique 802.1
Which statement about slow inter VLAN forwarding is true?
A. The VLAN is experiencing slowness in the point-to-point collisionless connection.
B. The VLANs are experiencing slowness because multiple devices are connected to the same hub.
C. The local VLAN is working normally, but traffic to the alternate VLAN is forwarded slower than expected.
D. The entire VLAN is experiencing slowness.
E. The VLANs are experiencing slowness due to a duplex mismatch.
Correct Answer: E
Common Causes of Slow IntraVLAN and InterVLAN Connectivity The symptoms of slow connectivity on a VLAN can be caused by multiple factors on different network layers. Commonly the network speed issue
What occurs on a Frame Relay network when the CIR is exceeded?
A. All TCP traffic is marked discard eligible.
B. All UDP traffic is marked discard eligible and a BECN is sent.
C. All TCP traffic is marked discard eligible and a BECN is sent.
D. All traffic exceeding the CIR is marked discard eligible.
200-105 vce Correct Answer: D
Committed information rate (CIR): The minimum guaranteed data transfer rate agreed to by the Frame Relay switch.
Frames that are sent in excess of the CIR are marked as discard eligible (DE) w
Refer to the exhibit.
RTA is configured with a basic configuration. The link between the two routers is operational and no routing protocols are configured on either router. The line shown in the exhibit is then added to router RTA. Should interface Fa0/0 on router RTB shut down, what effect will the shutdown have on router RTA?
A. A route to 172.16.14.0/24 will remain in the RTA routing table.
B. A packet to host 172.16.14.225 will be dropped by router RTA.
C. Router RTA will send an ICMP packet to attempt to verify the route.
D. Because router RTB will send a poison reverse packet to router RTA, RTA will remove the route.
Correct Answer: A
Static routes remain in the routing table even if the specified gateway becomes unavailable. If the specified gateway becomes unavailable, you need to remove the static route from the routing
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5. The EIGRP routing protocol is configured. You are required to troubleshoot and resolve the EIGRP issues between the various routers. Use the appropriate show commands to troubleshoot the issues.
Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is the cause for this misconfiguration?
A. The K values mismatch.
B. The AS does not match.
C. The network command is missing.
D. The passive-interface command is enabled.
200-105 exam Correct Answer: C
Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also
A. hop count
B. administrative distance
C. link bandwidth
D. link delay
E. link cost
Correct Answer: B
What Is Administrative Distance?
What is the advantage of using a multipoint interface instead of point-to-point subinterfaces when configuring a Frame Relay hub in a hub-and-spoke topology?
A. It avoids split-horizon issues with distance vector routing protocols.
B. IP addresses can be conserved if VLSM is not being used for subnetting.
C. A multipoint interface offers greater security compared to point-to-point subinterface configurations.
D. The multiple IP network addresses required for a multipoint interface provide greater addressing flexibility over point
200-105 dumps Correct Answer: B
You do not have to assign a separate subnet per sub-interface .if you\’re using a Class A network (10.x.x.x/8), you blow the whole network on a few connections (if you used VLSM, you could use a bette
We update our site on the regular base with a fresh new look and feel as well as new content and features. Preparation is so convenient when you know where to study from.Pass4itsure is one of the leading Cisco 200-105 dumps preparation providers and will make the test easier than your imagination. You can get so many reliable sources which insure you to pass the https://www.pass4itsure.com/200-105.html dumps exam, which gives you, practice question & answers to help you attempt all the questions easily.